Components Used The information in this document is based on these software and hardware versions: Internet Key Exchange Version 2 (IKEv2) Cisco IOS 15.1 (1)T or later For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. New here? Do you had to apply some NAT config? I have a working IPSEC project in GNS3 that uses csr1000 and 7200 routers, VTI interfaces, and IKEv1. Zscaler support IP-SLA HTTP probes to check the cloud proxy health, on traditional routers you are able to use 'track' features to, for example, change the admin distance of a static route based on the results of the IP-SLA test. Uses certificates for the authentication mechanism. I followed the guide and created the IPSEC interface on the service side instead of VPN0, unfortunately I'm getting a IKEv2 failure: IKEv2:% Getting preshared key from profile keyring if-ipsec1-ikev2-keyringIKEv2:% Matched peer block 'if-ipsec1-ikev2-keyring-peer'IKEv2:(SESSION ID = 0,SA ID = 0):Searching Policy with fvrf 0, local address X.X.X.XIKEv2:(SESSION ID = 0,SA ID = 0):Found Policy 'policy1-global'IKEv2-ERROR:Address type 1622425149 not supported. Let me ask you something - what format do you enter user/domain information in the client? I also had to mention the same ACL in the local policy for this to work. : crypto ikev2 profile default . This document describes Internet Key Exchange version 2 (IKEv2) debugs on Cisco IOS when a pre-shared key (PSK) is used. In my case even after adding the ACL entry there was another step which was needed to fix this tunnel. Customers Also Viewed These Support Documents, Branch router, ISR4451-X, version 16.12.1b. Thanks. Note. Configure Phase 1 Settings For IKEv1. Refer toCisco Technical Tips Conventionsfor more information on document conventions. IKEv2 Packet Exchange and Protocol Level Debugging, Technical Support & Documentation - Cisco Systems, Router 1 receives a packet that matches the crypto acl for peer ASA 10.0.0.2. First pair of messages is the IKE_SA_INIT exchange. Find answers to your questions by entering keywords or phrases in the Search bar above. The Responder tunnel usually comes up before the Initiator. "You can create the IPsec tunnel in the transport VPN (VPN 0) and in any service VPN (VPN 1 through 65530, except for 512). Palo Alto IP: 1.1.1.1 Cisco ASA IP: 2.2.2.2 Cisco ASA iKev2 and IPsec parameters: Router 1 then inserts this SA into its SAD. If the SA offers include different DH groups, KEi must be an element of the group the initiator expects the responder to accept. Customers Also Viewed These Support Documents, https://www.cisco.com/c/en/us/support/docs/security/flexvpn/115907-config-flexvpn-wcca-00.html. 01:52 PM Relevant Configuration:crypto ikev2 proposal PHASE1-prop encryption 3des aes-cbc-128 integrity sha1 group 2crypto ikev2 keyring KEYRNG peer peer1 address 10.0.0.2 255.255.255.0 hostname host1 pre-shared-key local cisco pre-shared-key remote cisco, *Nov 11 19:30:34.814: IKEv2:Got a packet from dispatcher *Nov 11 19:30:34.814: IKEv2:Processing an item off the pak queue *Nov 11 19:30:34.814: IKEv2:New ikev2 sa request admitted *Nov 11 19:30:34.814: IKEv2:Incrementing incoming negotiating sa count by one, *Nov 11 19:30:34.814: IKEv2:Next payload: SA, version: 2.0 Exchange type: IKE_SA_INIT, flags: INITIATOR Message id: 0, length: 344 Payload contents: SA Next payload: KE, reserved: 0x0, length: 56 last proposal: 0x0, reserved: 0x0, length: 52 Proposal: 1, Protocol id: IKE, SPI size: 0, #trans: 5 last transform: 0x3, reserved: 0x0: length: 8 type: 1, reserved: 0x0, id: 3DES last transform: 0x3, reserved: 0x0: length: 12 type: 1, reserved: 0x0, id: AES-CBC last transform: 0x3, reserved: 0x0: length: 8 type: 2, reserved: 0x0, id: SHA1 last transform: 0x3, reserved: 0x0: length: 8 type: 3, reserved: 0x0, id: SHA96 last transform: 0x0, reserved: 0x0: length: 8 type: 4, reserved: 0x0, id: DH_GROUP_1024_MODP/Group 2 KE Next payload: N, reserved: 0x0, length: 136 DH group: 2, Reserved: 0x0 N Next payload: VID, reserved: 0x0, length: 24 *Nov 11 19:30:34.814: IKEv2:Parse Vendor Specific Payload: CISCO-DELETE-REASON VID Next payload: VID, reserved: 0x0, length: 23 *Nov 11 19:30:34.814: IKEv2:Parse Vendor Specific Payload: (CUSTOM) VID Next payload: NOTIFY, reserved: 0x0, length: 21 *Nov 11 19:30:34.814: IKEv2:Parse Notify Payload: NAT_DETECTION_SOURCE_IP NOTIFY(NAT_DETECTION_SOURCE_IP) Next payload: NOTIFY, reserved: 0x0, length: 28 Security protocol id: IKE, spi size: 0, type: NAT_DETECTION_SOURCE_IP *Nov 11 19:30:34.814: IKEv2:Parse Notify Payload: NAT_DETECTION_DESTINATION_IP NOTIFY(NAT_DETECTION_DESTINATION_IP) Next payload: NONE, reserved: 0x0, length: 28 Security protocol id: IKE, spi size: 0, type: NAT_DETECTION_DESTINATION_IP, *Nov 11 19:30:34.814: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000000 CurState: IDLE Event:EV_RECV_INIT *Nov 11 19:30:34.814: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000000 CurState: R_INIT Event:EV_VERIFY_MSG *Nov 11 19:30:34.814: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000000 CurState: R_INIT Event:EV_INSERT_SA *Nov 11 19:30:34.814: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000000 CurState: R_INIT Event:EV_GET_IKE_POLICY *Nov 11 19:30:34.814: IKEv2:Adding Proposal default to toolkit policy *Nov 11 19:30:34.814: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000000 CurState: R_INIT Event:EV_PROC_MSG *Nov 11 19:30:34.814: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000000 CurState: R_INIT Event: EV_DETECT_NAT *Nov 11 19:30:34.814: IKEv2:(SA ID = 1):Process NAT discovery notify *Nov 11 19:30:34.814: IKEv2:(SA ID = 1):Processing nat detect src notify *Nov 11 19:30:34.814: IKEv2:(SA ID = 1):Remote address matched *Nov 11 19:30:34.814: IKEv2:(SA ID = 1):Processing nat detect dst notify *Nov 11 19:30:34.814: IKEv2:(SA ID = 1):Local address matched *Nov 11 19:30:34.814: IKEv2:(SA ID = 1):No NAT found *Nov 11 19:30:34.814: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000000 CurState: R_INIT Event: EV_CHK_CONFIG_MODE *Nov 11 19:30:34.814: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000000 CurState: R_BLD_INIT Event: EV_SET_POLICY *Nov 11 19:30:34.814: IKEv2:(SA ID = 1):Setting configured policies *Nov 11 19:30:34.814: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000000 CurState: R_BLD_INIT Event: EV_CHK_AUTH4PKI *Nov 11 19:30:34.814: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000000 CurState: R_BLD_INIT Event: EV_PKI_SESH_OPEN *Nov 11 19:30:34.814: IKEv2:(SA ID = 1):Opening a PKI session *Nov 11 19:30:34.815: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000000 CurState: R_BLD_INIT Event:EV_GEN_DH_KEY *Nov 11 19:30:34.815: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000000 CurState: R_BLD_INIT Event: EV_NO_EVENT *Nov 11 19:30:34.815: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000000 CurState: R_BLD_INIT Event:EV_OK_RECD_DH_PUBKEY_RESP *Nov 11 19:30:34.815: IKEv2:(SA ID = 1):Action: Action_Null *Nov 11 19:30:34.815: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000000 CurState: R_BLD_INIT Event:EV_GEN_DH_SECRET *Nov 11 19:30:34.822: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000000 CurState: R_BLD_INIT Event: EV_NO_EVENT *Nov 11 19:30:34.822: IKEv2:%Getting preshared key by address 10.0.0.1 *Nov 11 19:30:34.822: IKEv2:Adding Proposal default to toolkit policy *Nov 11 19:30:34.822: IKEv2:(2): Choosing IKE profile IKEV2-SETUP *Nov 11 19:30:34.822: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000000 CurState: R_BLD_INIT Event: EV_OK_RECD_DH_SECRET_RESP *Nov 11 19:30:34.822: IKEv2:(SA ID = 1):Action: Action_Null *Nov 11 19:30:34.822: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000000 CurState: R_BLD_INIT Event:EV_GEN_SKEYID *Nov 11 19:30:34.822: IKEv2:(SA ID = 1):Generate skeyid *Nov 11 19:30:34.822: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000000 CurState: R_BLD_INIT Event: EV_GET_CONFIG_MODE *Nov 11 19:30:34.822: IKEv2:IKEv2 responder - no config data to send in IKE_SA_INIT exch *Nov 11 19:30:34.822: IKEv2:No config data to send to toolkit: *Nov 11 19:30:34.822: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (R) MsgID = 00000000 CurState: R_BLD_INIT Event: EV_BLD_MSG *Nov 11 19:30:34.822: IKEv2:Construct Vendor Specific Payload: DELETE-REASON *Nov 11 19:30:34.822: IKEv2:Construct Vendor Specific Payload: (CUSTOM) *Nov 11 19:30:34.822: IKEv2:Construct Notify Payload: NAT_DETECTION_SOURCE_IP *Nov 11 19:30:34.822: IKEv2:Construct Notify Payload: NAT_DETECTION_DESTINATION_IP *Nov 11 19:30:34.822: IKEv2:Construct Notify Payload: HTTP_CERT_LOOKUP_SUPPORTED. The link you shared is for a vEdge setup, the one I've found is for cEdge 16.12.x. These debug commands are used in this document: *Nov 11 20:28:34.003: IKEv2:Got a packet from dispatcher *Nov 11 20:28:34.003: IKEv2: Processing an item off the pak queue *Nov 11 19:30:34.811: IKEv2:% Getting preshared key by address 10.0.0.2 *Nov 11 19:30:34.811: IKEv2:Adding Proposal PHASE1-prop to toolkit policyle *Nov 11 19:30:34.811: IKEv2:(1): Choosing IKE profile IKEV2-SETUP *Nov 11 19:30:34.811: IKEv2:New ikev2 sa request admitted *Nov 11 19:30:34.811: IKEv2:Incrementing outgoing negotiating sa count by one. It contains: ISAKMP Header (SPI/version/flags), SAi1 (cryptographic algorithm that IKE initiator supports), KEi (DH public Key value of the initiator), and N (Initiator Nonce). The first CHILD_SA is created for the proxy_ID pair that matches the trigger packet. All rights reserved. We may get it in march release if everything will be on track. At the moment,you can use service side ipsec in cedge. Be aware the static route will only be withdrawn from the routing table if the Tunnel goes down. The Notify Payload, is used to transmit informational data, such as error conditions and state transitions, to an IKE peer. Responder sends the response for IKE_AUTH. The documentation set for this product strives to use bias-free language. *Nov 11 19:30:34.835: IKEv2:KMI message 12 consumed. 189035: *Aug 8 14:01:22.161 Chicago: IKEv2:(SESSION ID = 8673,SA ID = 1):IKE Proposal: 1, SPI size: 0 (initial negotiation), AES-CBC SHA256 SHA256 DH_GROUP_2048_MODP/Group 14, 189036: *Aug 8 14:01:22.161 Chicago: IKEv2:(SA ID = 1):[IKEv2 -> PKI] Retrieve configured trustpoint(s), 189037: *Aug 8 14:01:22.161 Chicago: IKEv2:(SA ID = 1):[PKI -> IKEv2] Retrieved trustpoint(s): 'TP-self-signed-653483565', 189038: *Aug 8 14:01:22.161 Chicago: IKEv2:(SA ID = 1):[IKEv2 -> PKI] Get Public Key Hashes of trustpoints, 189039: *Aug 8 14:01:22.161 Chicago: IKEv2:(SA ID = 1):[PKI -> IKEv2] Getting of Public Key Hashes of trustpoints FAILED, 189040: *Aug 8 14:01:22.161 Chicago: IKEv2:Failed to retrieve Certificate Issuer list, 189041: *Aug 8 14:01:22.161 Chicago: IKEv2:(SESSION ID = 8673,SA ID = 1):Sending Packet [To 2.2.2.2:500/From 1.1.1.1:500/VRF i0:f0], Initiator SPI : 8A15E970577C6140 - Responder SPI : 0550071FA9DFE718 Message id: 0, SA KE N VID VID NOTIFY(NAT_DETECTION_SOURCE_IP) NOTIFY(NAT_DETECTION_DESTINATION_IP), 189042: *Aug 8 14:01:22.161 Chicago: IKEv2:(SESSION ID = 8673,SA ID = 1):Completed SA init exchange, 189043: *Aug 8 14:01:22.161 Chicago: IKEv2:(SESSION ID = 8673,SA ID = 1):Starting timer (30 sec) to wait for auth message, 189044: *Aug 8 14:01:22.429 Chicago: IKEv2:(SESSION ID = 8673,SA ID = 1):Received Packet [From 2.2.2.2:4500/To 1.1.1.1:500/VRF i0:f0], Initiator SPI : 8A15E970577C6140 - Responder SPI : 0550071FA9DFE718 Message id: 1, IDi NOTIFY(INITIAL_CONTACT) NOTIFY(Unknown - 16396) IDr AUTH CFG NOTIFY(ESP_TFC_NO_SUPPORT) NOTIFY(NON_FIRST_FRAGS) SA TSi TSr, 189045: *Aug 8 14:01:22.429 Chicago: IKEv2:(SESSION ID = 8673,SA ID = 1):Stopping timer to wait for auth message, 189046: *Aug 8 14:01:22.429 Chicago: IKEv2:(SESSION ID = 8673,SA ID = 1):Checking NAT discovery, 189047: *Aug 8 14:01:22.429 Chicago: IKEv2:(SESSION ID = 8673,SA ID = 1):NAT OUTSIDE found, 189048: *Aug 8 14:01:22.429 Chicago: IKEv2:(SESSION ID = 8673,SA ID = 1):NAT detected float to init port 4500, resp port 4500, 189049: *Aug 8 14:01:22.433 Chicago: IKEv2:(SESSION ID = 8673,SA ID = 1):Searching policy based on peer's identity '10.5.1.70' of type 'IPv4 address', 189050: *Aug 8 14:01:22.433 Chicago: IKEv2:found matching IKEv2 profile 'FlexVPN', 189051: *Aug 8 14:01:22.433 Chicago: IKEv2:% Getting preshared key from profile keyring keys, 189052: *Aug 8 14:01:22.433 Chicago: IKEv2:% Matched peer block 'DYNAMIC', 189053: *Aug 8 14:01:22.433 Chicago: IKEv2:Searching Policy with fvrf 0, local address 1.1.1.1, 189054: *Aug 8 14:01:22.433 Chicago: IKEv2:Found Policy 'ikev2policy', 189055: *Aug 8 14:01:22.433 Chicago: IKEv2:(SESSION ID = 8673,SA ID = 1):Verify peer's policy, 189056: *Aug 8 14:01:22.433 Chicago: IKEv2:(SESSION ID = 8673,SA ID = 1):Peer's policy verified, 189057: *Aug 8 14:01:22.433 Chicago: IKEv2:(SESSION ID = 8673,SA ID = 1):Get peer's authentication method, 189058: *Aug 8 14:01:22.433 Chicago: IKEv2:(SESSION ID = 8673,SA ID = 1):Peer's authentication method is 'PSK', 189059: *Aug 8 14:01:22.433 Chicago: IKEv2:(SESSION ID = 8673,SA ID = 1):Get peer's preshared key for 10.5.1.70, 189060: *Aug 8 14:01:22.433 Chicago: IKEv2:(SESSION ID = 8673,SA ID = 1):Verify peer's authentication data, 189061: *Aug 8 14:01:22.433 Chicago: IKEv2:(SESSION ID = 8673,SA ID = 1):Use preshared key for id 10.5.1.70, key len 7, 189062: *Aug 8 14:01:22.433 Chicago: IKEv2:[IKEv2 -> Crypto Engine] Generate IKEv2 authentication data, 189063: *Aug 8 14:01:22.433 Chicago: IKEv2:[Crypto Engine -> IKEv2] IKEv2 authentication data generation PASSED, 189064: *Aug 8 14:01:22.433 Chicago: IKEv2:(SESSION ID = 8673,SA ID = 1):Verification of peer's authenctication data PASSED, 189065: *Aug 8 14:01:22.433 Chicago: IKEv2:(SESSION ID = 8673,SA ID = 1):Processing INITIAL_CONTACT, 189066: *Aug 8 14:01:22.433 Chicago: IKEv2:(SESSION ID = 8673,SA ID = 1):Received valid config mode data. BR12-1X(config)# crypto ikev2 profile apple, BR12-1X(config-ikev2-profile)# config-exchange request, BR12-1X(config-ikev2-profile)# no config-exchange request. You can also check the output of theshow crypto sessioncommand on both routers; this output shows the tunnel session status as UP-ACTIVE. 08-08-2018 All but the headers of all the messages that follow are encrypted and authenticated. Create an ACL in Policies > Local Policy > Access Control ListsPermit port 500I also have the Default Action as Accept in my POC.Copy the ACL name (CTRL C) youll need it for the next step. Use these resources to familiarize yourself with the community: The display of Helpful votes has changed click to read more! Tunnel is up on the Responder. These messages negotiate cryptographic algorithms, exchange nonces, and do a Diffie-Hellman exchange. For more information, refer toIKEv2 Packet Exchange and Protocol Level Debugging. 2023 Cisco and/or its affiliates. Router 1 initiates the CHILD_SA exchange. Relevant Configuration:crypto ipsec transform-set TS esp-3des esp-sha-hmac crypto ipsec profile phse2-prof set transform-set TS set ikev2-profile IKEV2-SETUP, *Nov 11 19:30:34.831: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (I) MsgID = 00000000 CurState: I_BLD_AUTH Event:EV_GEN_AUTH *Nov 11 19:30:34.831: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (I) MsgID = 00000000 CurState: I_BLD_AUTH Event: EV_CHK_AUTH_TYPE *Nov 11 19:30:34.831: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (I) MsgID = 00000000 CurState: I_BLD_AUTH Event: EV_OK_AUTH_GEN *Nov 11 19:30:34.831: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (I) MsgID = 00000000 CurState: I_BLD_AUTH Event: EV_SEND_AUTH *Nov 11 19:30:34.831: IKEv2:Construct Vendor Specific Payload: CISCO-GRANITE *Nov 11 19:30:34.831: IKEv2:Construct Notify Payload: INITIAL_CONTACT *Nov 11 19:30:34.831: IKEv2:Construct Notify Payload: SET_WINDOW_SIZE *Nov 11 19:30:34.831: IKEv2:Construct Notify Payload: ESP_TFC_NO_SUPPORT *Nov 11 19:30:34.831: IKEv2:Construct Notify Payload: NON_FIRST_FRAGS Payload contents: VID Next payload: IDi, reserved: 0x0, length: 20 IDiNext payload: AUTH, reserved: 0x0, length: 12 Id type: IPv4 address, Reserved: 0x0 0x0 AUTHNext payload: CFG, reserved: 0x0, length: 28 Auth method PSK, reserved: 0x0, reserved 0x0 CFGNext payload: SA, reserved: 0x0, length: 309 cfg type: CFG_REQUEST, reserved: 0x0, reserved: 0x0, *Nov 11 19:30:34.831: SA Next payload:TSi, reserved: 0x0, length: 40 last proposal: 0x0, reserved: 0x0, length: 36 Proposal: 1, Protocol id: ESP, SPI size: 4, #trans: 3 last transform: 0x3, reserved: 0x0: length: 8 type: 1, reserved: 0x0, id: 3DES last transform: 0x3, reserved: 0x0: length: 8 type: 3, reserved: 0x0, id: SHA96 last transform: 0x0, reserved: 0x0: length: 8 type: 5, reserved: 0x0, id: Don't use ESN TSiNext payload: TSr, reserved: 0x0, length: 24 Num of TSs: 1, reserved 0x0, reserved 0x0 TS type: TS_IPV4_ADDR_RANGE, proto id: 0, length: 16 start port: 0, end port: 65535 start addr: 0.0.0.0, end addr: 255.255.255.255 TSrNext payload: NOTIFY, reserved: 0x0, length: 24 Num of TSs: 1, reserved 0x0, reserved 0x0 TS type: TS_IPV4_ADDR_RANGE, proto id: 0, length: 16 start port: 0, end port: 65535 start addr: 0.0.0.0, end addr: 255.255.255.255, NOTIFY(INITIAL_CONTACT) Next payload: NOTIFY, reserved: 0x0, length: 8 Security protocol id: IKE, spi size: 0, type: INITIAL_CONTACT NOTIFY(SET_WINDOW_SIZE) Next payload: NOTIFY, reserved: 0x0, length: 12 Security protocol id: IKE, spi size: 0, type: SET_WINDOW_SIZE NOTIFY(ESP_TFC_NO_SUPPORT) Next payload: NOTIFY, reserved: 0x0, length: 8 Security protocol id: IKE, spi size: 0, type: ESP_TFC_NO_SUPPORT NOTIFY(NON_FIRST_FRAGS) Next payload: NONE, reserved: 0x0, length: 8 Security protocol id: IKE, spi size: 0, type: NON_FIRST_FRAGS *Nov 11 19:30:34.832: IKEv2:(SA ID = 1):Next payload: ENCR, version: 2.0 Exchange type:IKE_AUTH, flags:INITIATORMessage id: 1, length: 556 Payload contents: ENCR Next payload: VID, reserved: 0x0, length: 528 *Nov 11 19:30:34.833: IKEv2:(SA ID = 1):SM Trace-> SA: I_SPI=F074D8BBD5A59F0B R_SPI=F94020DD8CB4B9C4 (I) MsgID = 00000001CurState: I_WAIT_AUTHEvent: EV_NO_EVENT, *Nov 11 19:30:34.832: IKEv2:Got a packet from dispatcher *Nov 11 19:30:34.832: IKEv2:Processing an item off the pak queue *Nov 11 19:30:34.832: IKEv2:(SA ID = 1):Request has mess_id 1; expected 1 through 1 *Nov 11 19:30:34.832:IKEv2:(SA ID = 1):Next payload: ENCR, version: 2.0 Exchange type:IKE_AUTH, flags:INITIATORMessage id: 1, length: 556 Payload contents: *Nov 11 19:30:34.832: IKEv2:Parse Vendor Specific Payload: (CUSTOM) VID Next payload: IDi, reserved: 0x0, length: 20 IDiNext payload: AUTH, reserved: 0x0, length: 12 Id type: IPv4 address, Reserved: 0x0 0x0 AUTH Next payload: CFG, reserved: 0x0, length: 28 Auth method PSK, reserved: 0x0, reserved 0x0 CFG Next payload: SA, reserved: 0x0, length: 309 cfg type: CFG_REQUEST, reserved: 0x0, reserved: 0x0 *Nov 11 19:30:34.832: attrib type: internal IP4 DNS, length: 0 *Nov 11 19:30:34.832: attrib type: internal IP4 DNS, length: 0 *Nov 11 19:30:34.832: attrib type: internal IP4 NBNS, length: 0 *Nov 11 19:30:34.832: attrib type: internal IP4 NBNS, length: 0 *Nov 11 19:30:34.832: attrib type: internal IP4 subnet, length: 0 *Nov 11 19:30:34.832: attrib type: application version, length: 257 attrib type: Unknown - 28675, length: 0 *Nov 11 19:30:34.832: attrib type: Unknown - 28672, length: 0 *Nov 11 19:30:34.832: attrib type: Unknown - 28692, length: 0 *Nov 11 19:30:34.832: attrib type: Unknown - 28681, length: 0 *Nov 11 19:30:34.832: attrib type: Unknown - 28674, length: 0 *Nov 11 19:30:34.832:SANext payload: TSi, reserved: 0x0, length: 40 last proposal: 0x0, reserved: 0x0, length: 36 Proposal: 1, Protocol id: ESP, SPI size: 4, #trans: 3 last transform: 0x3, reserved: 0x0: length: 8 type: 1, reserved: 0x0, id: 3DES last transform: 0x3, reserved: 0x0: length: 8 type: 3, reserved: 0x0, id: SHA96 last transform: 0x0, reserved: 0x0: length: 8 type: 5, reserved: 0x0, id: Don't use ESN TSiNext payload: TSr, reserved: 0x0, length: 24 Num of TSs: 1, reserved 0x0, reserved 0x0 TS type: TS_IPV4_ADDR_RANGE, proto id: 0, length: 16 start port: 0, end port: 65535 start addr: 0.0.0.0, end addr: 255.255.255.255 TSr Next payload: NOTIFY, reserved: 0x0, length: 24 Num of TSs: 1, reserved 0x0, reserved 0x0 TS type: TS_IPV4_ADDR_RANGE, proto id: 0, length: 16 start port: 0, end port: 65535 start addr: 0.0.0.0, end addr: 255.255.255.255.
Cqc Registered Manager Resignation,
The Balcony At Gourmet Glatt,
Xerox Printer All In One,
Articles C
